Avenson Audio IsoDIBuilding on the circuitry of the SmallDI, the IsoDI adds two optional isolation stages.The main signal path is still a clean, wide bandwidth transformerless FET amplifier, but the power is generated with an isolated DC to DC converter so that you can have true ground isolation and still run the IsoDI on phantom power.The IsoOut jack can be a buffered, transformer isolated output to feed amplifiers or other inputs that can compromise the performance of the main signal path if connected in parallel. Now there is a way to get a clean DI signal even when there is bad stage power that causes the amp to buzz from light dimmer hash! The switchable IsoOut / Parallel jack give you the flexibility to configure the jack as a summed input, a parallel connected output, or a transformer isolated output.All of this in a rugged palm sized aluminum extrustion that makes it easy to toss into your gig bag or pack into a road case. Specification's:Topology      transformerless FETInput Impedance     10 MΩInput Overload Level     +12 dBu at 1% THDGain     -0.2 dBFrequency Response     10 Hz - 100 kHz (+0/-0.25 db)Signal to Noise (A-weighted)     ≥ 108 dBOutput Impedance     150Ω (load ≥ 1kΩ )Power Requirements     P48 phantom power(~5 mA)Size     3.5 x 2.5 x 1.2 inches90 x 63 x 30 mmWeight     6.75 oz (191 g) For more information, please visit this products webpage. 

The IsoGtr expands on our circuitry of the IsoDI by adding 3 additional transformer isolated instrument outputs to serve as an isolated signal splitter for sending your guitar or instrument signal to up to 4 amplifiers or effects chains (3 transformer isolated + 1 Buffered Main Output), our same ultra-clean wide bandwidth unity gain FET Buffered DI output (XLR), as well as an XLR Line input for Re-amping to any of the available instrument level outputs, all powered conveniently with an external DC power supply. Housed in an extremely rugged 3.33″ x 5.25″ anodised aluminum extruded box (you know… the same type as our IsoDI that we ran over with a van to test under the most extreme tortures of the road). Built with high quality Neutrik TRS and XLR jacks, the IsoGtr will not only be a piece of gear you can trust to perform flawlessly on stage, but also a welcomed high quality part of your signal chain in any professional recording studio.

The new Mid-SideR came about as a response to hearing several requests from users of our original Mid-Side encoder/decoder box, and implementing them into a full rack space. First, we’ve added every bypass option we could think of in this Mid-Side processor. In addition to our overall Main Bypass, the Mid-SideR now offers a Mid-Side Encoder/Decoder Bypass (labeled Mid-Side Defeat) allowing the user to switch between using the available insert loop in Left-Right mode or Mid-Side mode, an Insert Bypass allowing the user to bypass the Mid-Side XLR out-in loop effectively bypassing their processing on the insert loop, to A/B they’re outboard gear processing in the Mid-Side insert loop with the original signal, as well as both a Mid Mute and a Side Mute to listen to exactly what you’re doing on only the Mid or Side. All this I/O is now conveniently accessed via an all high quality Neutrik XLR equipped rear panel. To take it a few steps further, we even added some additional EQ functionality as well as going to all high quality Rotary switches for the front panel controls. In addition to the original High Pass Filter on the Side(now with the easily recall-able rotary switch), we’ve added a High frequency Shelving EQ on the Side. Toggle between frequency selections of 5 kHz, 10 kHz, or 20 kHz to add presence or air on the Side information, effectively widening the Stereo Mix even more, or tame a bright mix by slightly lowering any harsh highs on the Side.

The STO-2 is a pressure transducer. So are your ears. No Coincidence. We started out looking for a natural sounding mic and this is what we came up with. Sold in matched pairs, (two ears right?) the STO-2's are perfect for capturing instruments that need no flattery. With a matched pair, stereo is no problem - Jecklin disk or spaced pair - it will sound like you are standing there.                                                 Specifications Transducer Type 0.25" Electret condenser pressure Polar Pattern Omni-Directional Output Level 5.25 (mV/Pa) Frequency Response 20 Hz - 20 kHz (+0/-2 db) Equivalent Noise (A-weighted) 28 dB Maximum SPL 145 dB (with 48V powering) Output Impedance 20Ω (load ≥ 1kΩ ) Power Requirements P48 phantom power (~6 mA) Weight 3.6 oz (100 g)For more information, please visit this products webpage.